Bearing Gard II
Bearing Isolator
- Equipment Type Pumps, electric motors, gearboxes, other rotating equipment
- Shaft Sizes 15.9 to 254 mm (0.625 to 10.000) inch
- Installs on bearing frames used in oil & gas, chemical, mining, pulp & paper, power and general industries
- Close tolerance labyrinth design locks out moisture, grit and dust, extending bearing life and increasing the MTBR of rotating equipment
- Easy to install one piece cartridge unit. On most equipment, requires no modification
- Same day shipment of popular sizes
- Lasts the life of the equipment
- Fits existing lip seal cavities
BGM
Magnetic Bearing Isolator
- Equipment Type Pumps, electric motors, gearboxes, other rotating equipment
- Shaft Sizes 15.9 to 152 mm (0.625 to 6.000) inch
- Installs on bearing frames used in oil & gas, chemical, mining, pulp & paper, power and general industries
- Rare earth magnets keep the seal faces closed
- Seals off the bearing housing completely from the effects of high humidity, temperature transients, heat and dust environments
- Easy to install design
- Coaxial face design provides the longest possible seal life
- Lasts up to 25 times longer than lip seals
Seal Gard I and II
Seal Chamber and Stuffing Box Protection
- Equipment Type Pumps
- Flow up to 2.6 l/min (40 gph)
- Volume up to 11.4 liter (3 gallon)
- Presssure up to 20.7 bar (300 psi), up to 8.6 bar (125 psi) at 140°C (300°F)
- Temperature 0 to 140°C (32 to 300°F)
- Connections 0.250 inch NPT
- Tough, unitized construction
- Seal Gard I controls flows at low flush rates in a Plan 32 system
- Seal Gard II provides dependable flow control to support dual seals while saving water costs and reducing seal water usage
- Good for paper stock sealing systems with Flowserve split seals and split flow reducers
- The vertical, tapered acrylic flow tube resists fouling
- Easy to read pressure gauge is vibration resistant and glycerine filled
- In the upset event of lost seal water pressure, the standard check valve stops the back-up of product and prevents contamination of the water supply
Magnetic Separator
Iron Particle Trap
- Flow up to 15 l/min (4 gpm)
- Pressure up to 103.4 bar (1500 psi)
- Temperature up to 204°C (400°F)
- Connections 0.500 inch NPT, MS-6670-DJ, 0.750 inch NPT, MS-0750-DJ
- Designed for Plan 23 mechanical seal injection flow and similar closed loop control lines
- Creates a magnetic field that separates and holds iron oxide particles from the process liquid
- Prevent iron particles from causing abrasion or damage
Cyclone Separator
Solid Particle Excluder
- Clean flow output from 3.4 - 30.3 l/min (0.9 - 8 gpm)
- Pressure up to 138 bar (2000 psi) at 330°C (650°F), up to 93 bar (1350 psi) at 455°C (850°F)
- Temperature up to 455°C (850°F)
- Connections 0.500 to 0.750 inch NPT or socket weld
- Offered in three different sizes based on flow rate and pressure
- Cyclone separators are designed to efficiently remove sand, pipe scale and other abrasive particles from Plan 31 injection flow to mechanical seals
- Separation is accomplished by centrifugal effects generated by differential pressure across the cyclone
- When properly configured, provides up to 99% separation efficiency
SLD
Synthetic Lubrication Device
- Process temperature up to 80°C (175°F)
- Ambient temperature -20 to 55°C (-4 to 130°F)
- Unitized system does not require air, electricity, or external water
- Ideal for single liquid seals with two hard faces and a Quench Containment Device (QCD)
- Single point lubricator allows each seal quench cavity to be satisfied independent of other equipment
- Used when no quench water is available, ideal for frequent automatic start/stop sequences and installations at remote field locations
- DS-920-OG DuraClear lubricant resists breakdown when mixed with pumpage, water or containments; optional DS-460-F lubricant is approved by USDA
- Customized dispensing rate for each application; provides precise lubrication for varying operating condition
